how to clean mass air flow sensor chevy equinox

To clean the MAF sensor you will need to locate and disconnect it from where its connected. The hood release is located under the dashboard on the drivers side.

Never Do This When Cleaning Your Mass Air Flow Sensor Youtube

Press the red clip slightly to unlock it.

. You need to get those wires as clean as possible. Remove the Sensor- Take care not to damage the wiring harness or the connector pins that receive the harness in the MAF. Wait for it to dry before you reinstall it.

Cleaning the Mass Airflow Sensor Locate the MAF Sensor Itll be in between the air filter and the throttle body. Remove the sensor from the housing. Unplug the electrical connector from the mass airflow sensor.

Dont scrub the parts. Once its dried you can reinsert the MAF sensor to your air intake hose. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will remove most of the.

If you have a hot wire mass air flow sensor make sure the. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone. Locate the mass airflow sensor near the engine air filter housing.

If you would like to try cleaning your old MAF sensor before buying a new one carefully spray the sensor wire with some CRC Mass Air Flow Sensor Cleaner. Once taken apart you will be able to move forward to the step cleaning the mass air flow sensor of. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone.

Cleaning dirty MAF sensor in Chevy Equinox Find the location of the MAF sensor in your Equinox it will be somewhere between the air filter box and the throttle. Clean the Sensor Now that youve removed your Equinoxs MAF. Mass air flow MAF sensors measure the amount of air entering the engine.

Also clean the sides of the part its housing its connectors and its terminals. Today I show you where your Mass Air Flow MAF Sensor is located and how to remove and clean it. Remove the screws that hold the mass airflow sensor in place.

Spray 10 to 15 spurts of the mass air flower cleaner onto the wire or plate. Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well. And lets get started with the actual step by step cleaning of the GM mass air flow MAF sensor Buick Chevrolet Oldsmobile Pontiac and GMC models.

When you are finished cleaning the sensor place it on the clothApply the cleanser. Alright enough of the bs. After having based the mass air flow sensor of your Chevrolet Equinox you will have to dismantle it.

Place the sensor on a towel for cleaning. You may break the wire or damage the plate. Open the hood of your Chevrolet.

Loosen the MAF hose clamps. Here I will give you detailed step-by-step methods to clean Mass Air Flow Sensor Chevy Silverado. Here I demonstrate how I cleaned my manifold absolute pressure MAP sensor and mass air flow MAF sensor in 2012 Equinox with 24L ecotec engine.

There will be a pair of wires inside. Apply the cleaner 10-15 blasts around the inside of the sensor will do. The OEM sensor was marked with a few sets of part numbers including AFH70M-124 7Y30 HALF 23366103 and 79300JI.

Remove The MAF Sensor From Vehicle. Remove the mass air flow sensor from the car or truck. Carefully remove the sensor from the air duct and disconnect the electrical connector.

This can be done quickly by taking a look at your engine bay. The Intake Air Temperature IAT sensor is also built into. Locate the mass airflow sensor near the engine air filter housing.

Spray at least 10 spurts of MAF cleaner onto the sensor and then. See below the different steps to stick to to execute this maintenance act. Allow the MAF sensor to dry completely before reinstalling it in the air duct.

Take your MAF sensor cleaner and clean the inside of the MAF sensor thoroughly so that cleaner touches each part of the wires. Once off your MAF sensor should look like the one in the photo. Unplug the electrical connector.

Step 1 Locate and disconnect the MAF sensor. You should only need to give it 1015 quick blasts around the interior of the sensorIn addition to this clean the sides of the component as well as its housing connections and terminalsIf you are using a hot wire mass air flow sensor you must ensure that the cleaner does not come into. The genuine GM compatible replacement mass air flow sensor part number is ACDelco 23366103.

Meaning 11 Symptoms Of A Bad Mass Air Flow Sensor Autovfix Com